|

Literature review on optimal cooling of magnetic coupling of chemical rotodynamic pump

Authors: Melnichuk E.S.
Published in issue: #10(27)/2018
DOI: 10.18698/2541-8009-2018-10-392


Category: Power, Metallurgic and Chemical Engineering | Chapter: Hydraulic Machines and Hydropneumatic units

Keywords: hydraulics, hydromachines, rotodynamic pump, pump drive, energy consumption, energy economy, auxiliary paths calculation, magnetic coupling, hermetic pump, blockage effect, pocket
Published: 31.10.2018

A review of literature on research studies of optimal cooling of magnetic coupling of chemical rotodynamic pump is performed. Today, this subject is particularly relevant. Issues of ecology, as well as fire and explosion safety at workplace are increasingly being raised. In order to solve this kind of problem in chemical and petrochemical industry, it is advisable to use hermetic pumps with magnetic clutch and hermetic electric motor. The main problems of using such pumps, identified as a result of the review, were problems of heat balance in cooled magnetic coupling and calculation of fluid flow in auxiliary paths. These problems are solvable, but highly energy-intensive, so the use of hermetic pumps is advisable in cases where the benefit exceeds risks and complexity of design.


References

[1] Kuznetsov V.S., Yarots V.V. Calculation of parameters for liquid expiration through cylindrical throttle channels in the mode of "blockage effect" existence. Mashinostroenie i inzhenernoe obrazovanie, 2016, no. 4, pp. 8–14.

[2] Lomakin V.O., Kukushkin P.A., Krylov V.I. Modernization of auxiliary cooling circuit of a magnetic coupling. Territoriya NEFTEGAZ [Oil and Gas Territory], 2017, no. 7-8, pp. 84–91.

[3] Lomakin V.O., Kuleshova M.S., Chaburko P.S., Baulin M.N. Complex wet end part optimization of hermetic pump with LP-TAU method. Nasosy. Turbiny. Sistemy [Pumps. Turbines. Systems], 2016, no. 1, pp. 55–61.

[4] Makarov K.A. On the physical meaning of Reynolds number and other criteria of hydrodynamic similarity. Inzhenernyy zhurnal: nauka i innovatsii [Engineering Journal: Science and Innovation], 2014, no. 1(25). Available at: http://engjournal.ru/catalog/eng/teormech/1185.html.

[5] Petrov A.I. Systems of the heat balance maintenance in modern test benches for centrifugal pumps. Mashiny i ustanovki: proektirovanie, razrabotka i ekspluatatsiya [Machines and Plants: Design and Exploiting], 2015, no. 5. Available at: http://maplants.elpub.ru/jour/article/view/24.

[6] Kuznetsov V.S., Shablovskiy A.S., Yarots V.V. Back pressure effects on some characteristics of fluid flow in valve slots. Inzhenernyy zhurnal: nauka i innovatsii [Engineering Journal: Science and Innovation], 2013, no. 4(16). Available at: http://engjournal.ru/catalog/machin/hydro/684.html.

[7] Borovin G.K., Protopopov A.A. Optimum number calculation of the centrifugal pump impeller blades. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 11. URL: http://engsi.ru/doc/747924.html.

[8] Protopopov A.A., Shul’zhitskiy A.A. Research on effect of supply voltage on maximum impeller pump head. Molodezhnyy nauchno-tekhnicheskiy vestnik, 2016, no. 3. URL: http://sntbul.bmstu.ru/doc/836477.html.

[9] Protopopov A.A., Zakharova E.V. Dynamics of small oscillations in a low-inertia rotor of a low-discharge centrifugal pump with hydrostatic bearings. Politekhnicheskiy molodezhnyy zhurnal [Politechnical student journal], 2017, no. 5. URL: http://ptsj.ru/catalog/pmc/hydr/95.html.

[10] Lomakin V. Chaburko P.S. Effect of stream vortex on pump hydraulic efficiency. Inzhenernyy vestnik [Engineering Bulletin], 2015, no. 10. Available at: http://engsi.ru/doc/820781.html.

[11] Artemov A.V., Shcherbachev P.V., Tarasov O.I. Using V-splines for constructing side half-spiral pump supply. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 12. Available at: http://engsi.ru/doc/742584.html.

[12] Gavryushina O.S., Mulyarchik I.G. Comparison of delivery-difference characteristic of pneumatic drives with rotary and translation actuating motors. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 12. Available at: http://engsi.ru/doc/745727.html.

[13] Lomakin V.O., Petrov A.I. Numerical modelling of thermal balance in cooled magnetic clutch of high-temperature hermetic pump. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 12. Available at: http://ainjournal.ru/doc/743214.html.

[14] Cheremushkin V.A., Petrov A.I., Chaburko P.S. Using stator blades in accessory tracts of hermetic pumps. Mashiny i Ustanovki: proektirovanie, razrabotka i ekspluatatsiya [Machines and Plants: Design and Exploiting], 2017, no. 2. Available at: https://maplants.elpub.ru/jour/article/view/59#.

[15] Petrov A.I., Poluektov D.A. Development of the new product line of centrifugal marine pumps for hot heat carried. Inzhenernyy vestnik [Engineering Bulletin], 2015, no. 10. Available at: http://engsi.ru/doc/816467.html.